柔性水囊潜堤消波特性的溃坝水槽试验研究     

陈本毅  赵西增  刘竹琴  周琪坤  卞婧 《海洋工程》2020,38(5):71-79

柔性水囊潜堤由橡胶制成，内部充水，具有结构简单、造价低廉等优点，能较好满足人工岛、跨海桥梁、海洋平台等基础设施建设工程对简单便携、拆装方便的临时防波堤的需求。为了探究柔性水囊潜堤的消波特性，在溃坝水槽内开展溃坝波与半圆柱形柔性水囊潜堤相互作用的试验研究，重点探究柔性水囊潜堤与溃坝波相互作用过程中水位变化特性，并与半圆柱刚性潜堤的性能进行比较；同时分析柔性水囊潜堤内部初始水压和浸没深度等参数对其消波性能的影响。结果表明：柔性水囊潜堤能够用作临时防波堤来衰减波浪；与半圆柱刚性潜堤相比，柔性水囊潜堤在降低溃坝波无量纲最大水位、提高消波性能方面更具优势；内部初始水压是影响柔性水囊潜堤消波性能的重要因素，适当降低内部初始水压，有利于增强柔性潜堤的变形程度，进而增加波能耗散，可获得更好的消波效果；而增加浸没深度即潜深，会使得柔性水囊潜堤对溃坝波的影响程度降低，消波效果减弱。  相似文献   

北部湾地区海砂填料的动力特性分析     

王家全  陈胜前  唐毅  黄世斌  黄钦政 《海洋工程》2020,38(5):149-155

为研究北部湾地区海砂填料的动力特性，采用高级动态三轴测试系统开展循环荷载下的动三轴试验，研究不同围压及不同动应力幅值对海砂动力特性的影响规律。试验结果表明：轴向累计应变随围压增加而减小，围压150 kPa时振次10 000后应变仅为3%；随着动应力幅值的增大轴向累积应变随之增大，且达到破坏标准的时间越短。动弹性模量随着动应力幅值和围压的增加而增大，不同围压下动弹性模量随动应变的增加出现先骤减再略减后稳定的发展趋势，ε_d>0.3%后开始趋于稳定；不同动应力幅值下动弹性模量出现先增后减直至稳定的趋势，其中动应力幅值对动弹性模量有明显的影响，围压影响相对较小。孔压比随动应力幅值增加而减小，随围压增加而增加。  相似文献   

Impacts of confining pressure and safety thickness on water and mud inrush in weathered granite     

Jinquan Liu  Weizhong Chen  Zhiping Deng  Taogen Liu 《Marine Georesources & Geotechnology》2020,38(2):144-153

Abstract

Due to the strong disintegration and water erosion of completely weathered granite, water and mud inrush disasters are apt to take place in this zone during underwater tunnel construction. The pore, compactness, seepage path length, fracture geometries and their interconnections for water and mud transfer are strongly influenced by confining pressure and waterproof-resistant slab safety thickness. In order to inspect the influence, a series of experiments based on a self-designed testing system and non-Darcy testing method were performed. The results indicated that the water and mud inrush evolution increased with the increase of confining pressure and decreased with the increase of safety thickness. In particular, the confining pressure mainly influences the initial evolution stage, and a critical safety thickness to prevent water and mud inrush is obtained. Besides, the non-Darcy testing method results shows that the water and mud inrush evolution affects the influence of non-Darcy flow. For example, while the safety thickness was smaller than the critical value, the evolution was large and unstable and its behavior transferred into nonlinear. In this case, the flow changed to non-Darcy flow.  相似文献   

Effect of microstructure on stress–strain and pore-pressure response of sabarmati sand under the influence of mica     

P. Seethalakshmi 《Geomechanics and Geoengineering》2020,15(2):123-139

ABSTRACT

Micaceous soil is believed to be detrimental for civil engineering constructions due to the effect of high compressibility, low compacted density and low shear strength. Individual mica particle has numerous intact mica flakes foliated over each other making it flexible upon loading and rebound upon unloading due to its low hardness and resilient nature. Hence, micaceous soils with mica content more than 10% are considered undesirable for highway pavements, embankments and railway track constructions. When platy mica particles are sufficiently numerous to interact with spherical sand particles, bridging and ordering phenomena are augmented within the soil mass creating unique sand-mica particle orientation (MS microstructure) unlike sand-sand particle orientation (PS microstructure). The current experimental research was conducted to evaluate the variation in stress–strain, pore pressure and effective stress path response of Sabarmati sand under the influence of mica (sand with 30% mica and pure sand) with MS and PS microstructure respectively. Effect of particle crushing on stress–strain and pore pressure response was also studied on Sabarmati sand with MS and PS microstructure. Distinctive macroscopic response was observed in Sabarmati sand with MS microstructure under the influence of mica as well as mica particle crushing.  相似文献   

AN EXPERIMENTAL STUDY ON THE PROCESS OF INTERGRANULAR PRESSURE SOLUTION OF PLAGIOCLASE GOUGE UNDER HIGH TEMPERATURE AND PRESSURE: METHOD AND PRELIMINARY RESULTS          下载免费PDF全文

ZHANG Shu  HE Chang-rong 《地震地质》2019,41(4):1012-1026

To understand the mechanism of lower-crust earthquake and slow slips, it is necessary to study the frictional properties of mafic rocks and their major rock-forming minerals. Previous studies have performed a series of experimental researches on gabbro, basalt and their major constituents. According to the results of previous experiments, frictional sliding of plagioclase under hydrothermal conditions(100~600℃)shows a property of velocity weakening, and the experimental results show that both the direct rate effect parameter(a)and the healing effect parameter(b)increase with temperature, a typical feature for thermally-activated processes. Velocity weakening means property of a shear band that has a stronger friction healing effect than the direct rate effect in the rate and state friction constitutive framework, and the healing effect(b value)in constitutive relation mainly reflects the increase in contact area with time under hydrothermal conditions, with some minor effect of structural changes. Since the microphysical mechanism of feldspar minerals at the contacts is mainly brittle cataclasis for temperatures below 600℃, the significant frictional healing effect in this case can only be explained by the mechanism of pressure solution. In order to determine if the dissolution process of plagioclase actually occurs on the laboratory time scale, we conducted hydrostatic experiments on plagioclase powder samples under hydrothermal conditions whereby frequent contact switch between particles seen in frictional sliding experiments can be avoided, making the observation on the dissolution sites possible. Experimental temperatures were 400℃ and 500℃, with confining pressure of 90~150MPa, pore pressure of 30MPa, with 2mm initial thickness of fault gouge. The mechanical data show that a creep process occurred in the plagioclase fault gouge in the experimental temperature and pressure range; and the microstructures of the experiment show that precipitation of new grains is prevalent as the product of pressure solution process between plagioclase particles. At the same time, it is observed that the contact points have an appearance similar to fused, fuzzy structure as signatures of dissolution. The results of our experiments provide a definite experimental evidence for the healing mechanism in friction of plagioclase and for the theoretical relation between unstable slip and the pressure solution process. The results of the experiments are summarized as follows: (1)Drainage rate of pore water in plagioclase gouge was high in the first few hours of experiment, but gradually decreases over time for both temperature and pressure series of experiments slowing down to a steady state. This feature indicates that there is a creep process that evolves inside the plagioclase gouge. In the temperature-series experiments, the drainage rate of the pore water in the plagioclase gouge at 400℃ is relatively low than the cases for higher temperatures. Thus, the applied temperature is positively correlated with the creep of plagioclase gouge. (2)Scanning electron microscopy(SEM)observations of the experimentally deformed samples were performed on thin sections cut along the sample axis. Firstly, from the images of microstructure, it was found that the degree of particle fracture became more significant at a higher effective pressure, with smaller pore volume between particles. In the temperature-series experiments it was found that the degree of compaction of plagioclase gouge increased with increasing temperature. Precipitation of plagioclase grains in layered structures was generally observed in high-magnification images, indicating the presence of pressure solution processes. Contact points were also found to be in a state of ambiguity that seems to be a fused morphology, but the details of the structure remain to be determined by further observations. The above results indicate that the pressure solution process of plagioclase particles can occur on a typical laboratory time scale, and the results of this study provide robust experimental evidences for the theory that links between pressure solution and the mechanism of frictional healing and unstable slips for plagioclase.  相似文献   

景观建筑挡土墙优化设计后抗震性能的实验测试研究          下载免费PDF全文

牛艳玲  王洁宁 《地震工程学报》2019,41(3):596-600

目前的景观建筑设计中往往更注重建筑的景观性,而忽略了建筑的安全稳定性,导致景观建筑的整体抗震效果较差,在景观建筑设计中加入挡土墙设计可以有效提高其抗震性。为此,设计一种具有一定抗震性能的景观建筑挡土墙,利用建筑施工过程中保留的复合纤维材料、建筑垃圾以及纤维绳等作为土墙填充物,并加入具有一定抗拉能力的拉筋材料,以保持土墙内部的稳定性。考虑景观建筑通常注重外观视觉效果,使用"平改坡"设计,在墙体表面种植具有一定视觉冲击的植物,增加土墙自重,促进土墙整体结构的稳定性。分析挡土墙后面无限倾斜填土受力状态,选取菱形微小单元体作为研究对象,计算景观建筑的挡土墙土压力强度。实验证明,优化设计的景观建筑挡土墙结构可以有效增强景观建筑的整体抗震能力。  相似文献   

郯庐断裂带新沂—泗洪段土壤气Rn体积活度和CO2浓度特征研究     

缪阿丽  张扬  方震  李锋  王维  高力 《地震》2019,39(1):48-57

郯庐断裂带江苏段地区4个剖面进行了土壤气Rn体积活度和CO₂浓度测量结果显示, 自北向南土壤气Rn体积活度均值分别为22.9 kBq/m³、 35.5 kBq/m³、 40.2 kBq/m³、 26.6 kBq/m³; 自北向南土壤气CO₂浓度均值分别为0.669%、 0.400%、 0.503%、 1.109%。 土壤气Rn体积活度和CO₂的浓度在空间分布上具有较好的一致性, 这可能与CO₂是Rn的载气有关。 综合分析土壤气Rn和CO₂测量结果以及水准资料可得, 2017年土壤气Rn高值出现在晓店段可能与区域应力应变调整有关。 本研究不仅为研究区以后的土壤气研究提供了参考, 同时也可为研究区的构造活动研究提供地球化学资料参考。  相似文献   

汤东活动断裂带土壤H2、Rn地球化学特征     

胡宁  马志敏  王明亮  王宇  娄露玲  夏修军  张宝山  王文净  郭德科 《地震》2019,39(2):174-182

为研究汤东断裂带土壤气体地球化学特征及其所反映的构造地球化学背景, 采用野外监测的方法分析了张河村与邢李庄村两条测线的土壤H₂、 Rn分布特征。 结果表明, 张河村H₂浓度、 Rn活度浓度的分布范围分别为0.24×10^-6～174.7×10^-6、 13.3～69.8 kBq·m^-3, 背景值分别为14.26×10^-6, 24.8 kBq·m^-3。 邢李庄测线H₂浓度、 Rn活度浓度的分布范围11.8×10^-6～67.06×10^-6、 43.6～72.6 kBq·m^-3, 背景值分别为37.13×10^-6、 72.6 kBq·m^-3。 张河村测线在90～105 m处, H₂、 Rn出现强烈高值异常, 而120～150 m处出现高值异常。 异常值位于断裂带附近, H₂、 Rn气体测值对断裂位置具有良好的指示作用。 气体异常主要受汤东活动断裂构造控制, 汤东断裂下方的深大断裂和汤阴地堑中下地壳的低速体对深部气体释放有重要作用。  相似文献   

飑线对定点地形变观测的影响特征与机理——以陕西关中盆地为例     

杨小林  危自根  杨锦玲  王党席 《中国地震》2019,35(3):465-475

2013年7月31日～8月1日陕西关中盆地爆发了一次强飑线灾害性天气过程,为揭示此次飑线生命史期间对定点地形变观测的影响特征与机理,本文结合多普勒天气雷达和气象资料,系统分析了关中盆地内4个地形变观测数据。结果表明:(1)飑线过境时的短时气压突变是造成定点地形变的主要原因,引起最大的地倾斜和地应变分别达9.70×10~(-3″)和21.02×10~(-9);(2)气压变幅与地形变的弹性响应量具有较好的线性关系,二者持续时间较一致,为2～4h,其中,钻孔体应变的动态气压系数达4.04×10~(-9)/h Pa;(3)宝鸡、乾陵和华阴台对飑线的响应能力较好,西安台则较差;(4)除水管仪外,垂直摆、洞体应变和钻孔体应变等对飑线的响应均较为灵敏。上述结果有助于合理识别和科学推定飑线所导致定点地形变异常变化的物理本质,进而减少实际业务中的误判;同时,还能为定点地形变观测台站的科学选址、仪器的优化布设及不同空间尺度大气负荷模型的实证等提供重要的参考依据。  相似文献   

水库温室气体净通量评估模型(G-res Tool)及在长江上游典型水库初步应用     

张斌  李哲  李翀  陈永柏  郭劲松 《湖泊科学》2019,31(5):1479-1488

目前准确量化温室气体排放量已成为气候变化研究和政策制定的关键.在IPCC水库温室气体净通量的概念性框架下，国际水电协会汇总分析了全球223座水库的CO₂和CH₄研究成果，构建了G-res Tool，其可以用于评估已建或待建水库在长时间尺度下的温室气体净通量.本文介绍了G-res Tool模型的基本原理与模型框架，利用模型内置数据库中所涉及的中国长江上游12座典型水库数据进行初步应用分析，12座水库温室气体净通量平均值为88.17 g CO₂e/（m²·a），在全球约7000座水库中所处水平为11.67%，处于低阈值范围.在水库温室气体净通量分析结果中，其他非相关人类活动产生的水库温室气体通量（UAS）在蓄水后总通量（Post）中所占比重远高于蓄水前温室气体通量（Pre）.长江上游水库蓄水后的CH₄和CO₂通量对于温室效应的贡献量相当.通过将G-res Tool模型蓄水后的温室气体通量评估结果和所涉及到的12座水库中已发表的数据对比分析发现，G-res Tool具有简便、适用面广等特点.但G-res Tool毕竟仍为经验性模型，其基本原理和模块设计上的内在缺陷在很大程度上限制了其应用范围并造成了一定的不确定性.对个案水库而言，长期跟踪观测与机理研究仍是未来减少水库温室气体净通量不确定性的关键.  相似文献